| 310-800 MULTI-PURPOSE BLADE |
|
Blade diam. = 10"
Bore = 5/8"
Teeth = 80
Grind = Triple chip
Kerf width = 0.126"
Hook angle = minus 5-deg.
Jesada's Multi-Purpose blades are ideal for virtually any project requiring smooth cuts in melamine, thin-walled aluminum, other non- ferrous metals or plastic. They feature a 5-degree negative hook to avoid tearing the workpiece. When cutting aluminum please take special care to be sure the workpiece is secure, controlled and free of vibration.
|
| 210-240 THIN-KERF RIPPING BLADE |
|
Blade diam. = 10"
Bore = 5/8"
Teeth = 24
Grind = Flat
Kerf width = 0.097"
Hook angle = 20-deg.
These Thin-kerf blades feature the same design and micrograin carbide teeth as Jesada's standard blades, but their teeth and steel plate offer a thinner profile. They are ideal for under powered saws that might bog down with a thicker blade. It is advised that Blade Stabilizers (see SBS range) are used with these blades.
|
| 112-901 MITER SAW BLADE |
|
Blade diam. = 12"
Bore = 1"
Teeth = 90
Grind = 4/30-deg. Alternate Top Bevel
Kerf width = 0.110"
Hook angle = minus 5-deg.
Jesada miter saw blades work so well because of their 5- degree negative rake hook that keeps the the blade from pulling itself through the workpiece, so the teeth have time to cut cleanly. Second, their special ATB grind produces a remarkably smooth cut in the finest molding. Altogether, they're ideal for any miter application.
|
| 110-801 MITER SAW BLADE |
|
Blade diam. = 10"
Bore = 5/8"
Teeth = 80
Grind = 4/30-deg. Alternate Top Bevel
Kerf width = 0.110"
Hook angle = minus 5-deg.
Jesada miter saw blades work so well because of their 5-degree negative rake hook that keeps the the blade from pulling itself through the workpiece, so the teeth have time to cut cleanly. Second, their special ATB grind produces a remarkably smooth cut in the finest molding. Altogether, they're ideal for any miter application.
|
| 108-240S JOINT MASTER DADO SET |
|
Blade diam. = 8" Best price anywhere!
Bore = 5/8"
Teeth = 24
Grind = 20-deg. Alternate Top Bevel
Kerf width = 1/4 to 29/32"
Hook angle = minus 5-deg.
Some manufacturers' dado sets leave deep scores in the bottom of the cut because they leave the points of their outside blades as much as 0.20" higher than their chippers. Jesada demand better from their 8" diam., 5/8" bore, Joint Master Dado set. The points of their blades are only 0.005" higher than the chippers, so they leave virtually no unsightly marks. Jesada's set still lets you slice dadoes in hard or soft wood - plywood or composites without tear-out or chipping. The Joint Master also includes the 3/32" Ply-Groove chipper. With this in-between size (the set also includes four 1/8" chippers and one 1/16" chipper) you can adjust the cutting width to give a snug fit to undersized plywood. Set up any cut between 1/4 and 29/32".
|
| 110-800 ULTRA-CUT LAMINATE BLADE |
|
Blade diam. = 10"
Bore = 5/8"
Teeth = 80
Grind = 40-deg. Alternate Top Bevel
Kerf width = 0.125"
Hook angle = 5-deg.
Ultra- Cut is Jesada's premium fine-cutting blade. The teeth are ground with a very high, 40-degree, top bevel angle. These high, sharp points slice the edge of the kerf first to eliminate chipping, even in expensive two-sided melamine.
|
| 110-600 GENERAL PURPOSE BLADE |
|
Blade diam. = 10"
Bore = 5/8"
Teeth = 60
Grind = 30-deg. Alternate Top Bevel
Kerf width = 0.104"
Hook angle = 5-deg.
These general purpose blades are perfect for all-round table saw or radial arm use. Their carbide teeth are set with a positive hook and feature 30-degree alternate top bevel, so they provide clean cuts in almost any application.
|
